Operating Systems Category - Page 208 of 1028 - CNX Software

February 25, 2022July 31, 2022 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

RISC-V design challenge – Get a free board, RISC-V chips, and cash prizes

A little while ago, I wrote about WCH CH32V307 32-bit RISC-V MCU that was found in a board with eight UART ports that could be controlled over Ethernet or USB, and the company has released some source code to use the board while inviting the community to submit pull requests to the project. But now WCH, RT-Thread, LCSC, and EasyEDA have joined hands to launch the RISC-V design challenge where the companies will provide a free board or two RISC-V chips to selected participants, as well as cash prizes with up to $1000 offered to the best projects. The companies have prepared 300 boards and 200 chips for this contest. All you need to do to get a chance to get either one CH32V307V-EVT-R1 development board or two CH32V307 RISC-V microcontrollers is to enter your contact and project details in this Google form by April 30, 2022. The conditions are […]

February 25, 2022March 3, 2022 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Raspberry Pi 5G Development Kit to ship with Quectel RM50xQ or Telit FN980 modem

SixFab is now taking pre-orders for its “Raspberry Pi 5G Development Kit” equipped with either Quectel RM50xQ or Telit FN980 5G modem fitted to SixFab’s Raspberry Pi 5G HAT, all housed in a plastic and acrylic enclosure with four antennas. The selected modems rely on the worldwide 5G NR Sub-6GHz and mmWave frequency bands, and the company says a data throughput of up to 5.0 Gbps (download) and 1.0 Gbps (upload) is possible with the kit. SixFab explained the 5G devkit is designed to help with the development, optimization, and testing of MTC (Machine-type Communication) and M2M projects leading to products such as IoT gateways, indoor and outdoor CPE, high bitrate video streaming, real-time sensor data broadcasting, high-speed mobile 5G hotspot, etc. SixFab Raspberry Pi 5G Development Kit specifications: Works with Raspberry Pi 4 or compatible SBC’s with USB 3.0 port Raspberry Pi 5G HAT with M.2 socket optionally fitted […]

February 24, 2022October 17, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

Pigeon RB700 is a DIN Rail automation controller with RS-485, RS-232, Ethernet, CAN FD, 1-WIRE, RS-232, and more

We’re covered DIN-Rail industrial computers powered by Raspberry Pi CM4 module, but Kristech’s Pigeon RB700 automation controller may be the one with the most features so far thanks to two RS-485 ports, two Ethernet ports, CAN FD, 1-WIRE, RS-232, 12 digital inputs (8 optoisolated, 4 dry contacts), and 8 digital outputs. That’s for the common features present in all variants including RB700 Essense. The RB700 Standard model adds UPS, HDMI, analog I/Os, and TPM, while the RB700 Advance is further equipped with two M.2 sockets (for SSD and/or cellular modem) and two additional RS-232 ports. Pigeon RB700 specifications: Supported SoM- Raspberry Pi CM4 with up to 8GB RAM, up to 32GB flash, optional WiFi 5 and Bluetooth 5.0 module Video Output (Standard and Advance) – HDMI port Networking – 2x Ethernet ports USB – 2x or 3x USB 2.0 ports Wired communication interfaces 3x RS-232, 2x RS-485, CAN FD, 1-Wire […]

February 23, 2022 by Ian W MORRISON (Linuxium) - 4 Comments

Aerofara Aero 2 Pro Review – A Celeron N5105 mini PC tested with Windows 11, Ubuntu 20.04

Aerofara’s Aero 2 Pro is an Intel Jasper Lake mini PC and one of the very few new mini PCs to include a VGA port. Aerofara kindly sent one for review and I’ve looked at performance running both Windows and Ubuntu. Aero 2 Pro Hardware Overview The Aero 2 Pro physically consists of a 120 x 120 x 23mm (4.72 x 4.72 x 0.91 inches) rectangular metal case with inset front and back plastic panels. As an actively cooled mini PC, it uses Intel’s 10 nm Jasper Lake N5105 processor which is a quad-core 4-thread 2.00 GHz Celeron processor boosting to 2.90 GHz with Intel’s UHD Graphics. The front panel is bereft of anything save a pinhole which is illuminated blue when the device is powered on. The rear panel includes the power jack, a USB 3.1 port, an HDMI port, an Ethernet port, a 3.5mm headphone jack, and a […]

February 20, 2022June 2, 2022 by Jean-Luc Aufranc (CNXSoft) - 74 Comments

Fixing performance issues with Realtek RTL8156B 2.5GbE USB dongle in Ubuntu

A few days ago, I reviewed a USB 3.0 to 2.5 Gbps Ethernet adapter based on Realtek RTL8156B chip in Ubuntu 20.04, and let’s say the reliability and performance were underwhelming. I got some recommendations like changing cables, the MTU size, etc… Playing around with cables did no help, but one comment mentioned the cdc_ncm driver could be the issue, followed by another saying that updating to Linux kernel 5.14 should install the correct r8152 driver… So I just did that:

sudo apt install linux-oem-20.04d

1	sudo apt install linux-oem-20.04d

This upgraded Linux 5.13 (shipped with Ubuntu 20.04 + HWE) to Linux 5.14, but still no luck as the system kept using the cdc_ncm driver with a half-duplex link:

jaufranc@cnx-laptop-4:~$ inxi -n
Network:
  Device-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet 
  driver: r8169 
  IF: enp2s0f1 state: down mac: 98:28:a6:0f:06:07 
  Device-2: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter 
  driver: ath10k_pci 
  IF: wlp3s0 state: up mac: 70:c9:4e:b7:84:77 
  Device-3: Realtek USB 10/100/1G/2.5G LAN type: USB driver: cdc_ncm 
  IF: enx1cbfced40321 state: up speed: 2500 Mbps duplex: half 
  mac: 1c:bf:ce:d4:03:21 
jaufranc@cnx-laptop-4:~$ uname -a
Linux cnx-laptop-4 5.14.0-1022-oem #24-Ubuntu SMP Mon Jan 31 16:00:31 UTC 2022 x86_64 x86_64 x86_64 GNU/Linux

jaufranc@cnx-laptop-4:~$ inxi -n

Network:

Device-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet

driver: r8169

IF: enp2s0f1 state: down mac: 98:28:a6:0f:06:07

Device-2: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter

driver: ath10k_pci

IF: wlp3s0 state: up mac: 70:c9:4e:b7:84:77

Device-3: Realtek USB 10/100/1G/2.5G LAN type: USB driver: cdc_ncm

IF: enx1cbfced40321 state: up speed: 2500 Mbps duplex: half

mac: 1c:bf:ce:d4:03:21

jaufranc@cnx-laptop-4:~$ uname -a

Linux cnx-laptop-4 5.14.0-1022-oem #24-Ubuntu SMP Mon Jan 31 16:00:31 UTC 2022 x86_64 x86_64 x86_64 GNU/Linux

But then I thought I may have to use udev rules to prevent loading the cdc_ncm driver, and there’s indeed 50-usb-realtek-net.rules in r8152 driver to do just that. So I copied the file in /etc/udev/rules.d/ folder. Since I […]

February 18, 2022 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

VIA SOM-9X35 Starter Kit features MediaTek i350 Arm processor for edge AI devices

VIA has just introduced the SOM-9X35 Starter Kit based on MediaTek i350 quad-core Cortex-A53 processor with AI accelerator and HiFi4 DSP designed for Edge AI devices in the retail, commercial, and industrial sectors. The kit is comprised of the SOM-9X35 module with MediaTek i350 SoC, up to 4GB RAM, 16GB eMMC flash, and WiFI 5 + Bluetooth 5.0 wireless module, as well as the VIA VAB-935 3.5-inch carrier board, a 7-inch 1024×600 touch panel display, a 13MP camera module, two speakers and microphone, and accompanying accessories. VIA SOM-9X35 Starter Kit specifications: SOM-9X35 System-on-Module SoC – MediaTek i350 (MT8365) quad-core Arm Cortex-A53 processor @ up to 2.0 GHz, Arm Mali-G52 MC1 up to 800Mhz with support for OpenGL ES, OpenCL, and Vulkan APIs, MediaTek APU 1.0 AI Processor up to 500MHz (285 GMACs), HiFi4 DSP System Memory – 2GB LPDDR4 SDRAM (1GB/4GB optional) Storage – 16GB eMMC flash Connectivity – MediaTek […]

February 17, 2022August 11, 2022 by Jean-Luc Aufranc (CNXSoft) - 28 Comments

USB 3.0 to 2.5Gbps Ethernet adapter review

Late last month, I received hardware to test 2.5GbE and WiFi 6 with namely a Radxa E25 SBC, Xiaomi AX6000 WiFi 6 router, and an 8-port TP-Link 2.5GbE switch. I intended to start testing 2.5GbE networking with UP Xtreme i11 mini PC and Radxa E25, but I thought it might be a good idea to get a USB 3.0 to 2.5Gbps Ethernet adapter just in case. I purchased a no-name dongle for under $15 (475 THB on Lazada) in Thailand, but a USB 3.0 dongle that looks exactly the same can also be purchased on Aliexpress with either a USB Type-A port or a USB Type-C port. There’s some issue with Radxa E25 (it won’t boot it), so I ended up testing the dongle with UP Xtreme i11 mini PC. USB 3.0 to 2.5Gbps Ethernet adapter unboxing The package, marked “USB to LAN Gigabit Ethernet Adapter”, has “USB 3.0” and […]

February 17, 2022June 10, 2023 by Ian W MORRISON (Linuxium) - 12 Comments

Beelink GTR5 Review – An AMD Ryzen 9 mini PC tested with Windows 11, Ubuntu 20.04

Beelink’s GTR5 is their most powerful mini PC to date and has been released as part of their ‘GT’ series of slightly larger mini PCs that are notable for expandable storage configurations together with multiple ports and characterized by the inclusion of a fingerprint scanner. Featuring an AMD Ryzen 9 mobile processor with Radeon Graphics, Beelink kindly sent one for review and I’ve looked at performance running both Windows and Ubuntu. Hardware Overview The Beelink GTR5 physically consists of a 168 x 120 x 39mm (6.61 x 4.72 x 1.54 inches) rectangular metal case. As an actively cooled mini PC, it uses AMD’s ‘Zen 3’ Ryzen 9 5900HX processor which is an eight-core 16-thread 3.3 GHz mobile processor boosting up to 4.6 GHz together with Radeon Graphics. The front panel has an illuminated power button, a ‘CLR CMOS’ button, a USB 3.1 port, a Type-C USB 3.1 port, and a […]