Linux Category - Page 95 of 603 - CNX Software

June 13, 2023June 13, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

CompuLab UCM-iMX93 – A miniature NXP i.MX 93 module with WiFi 5 & Bluetooth 5.3

CompuLab UCM-iMX93 is a miniature system-on-module powered by the new NXP i.MX93 Cortex-A55 AI processor family with up to 2GB RAM and 64GB eMMC flash. The tiny 38x28mm features a Gigabit Ethernet PHY, a WiFi 5 and Bluetooth 5.3 wireless modules, and plenty of multimedia, communication, and peripheral interfaces through two 100-pin high-density connectors including display and camera interfaces, USB ports, CAN FD, and up to 79 GPIOs. UCM-iMX93 specifications: SoC – NXP i.MX9352 or i.MX9331 dual-core/single-core Arm Cortex-A55 @ 1.5 GHz (industrial) / 1.7 GHz (commercial) with Arm Cortex-M33 real-time core @ 250 MHz, Arm Ethos U65 microNPU System Memory – 512MB to 2GB LPDDR4 Storage – 8GB to 64GB eMMC flash Networking Gigabit Ethernet PHY Certified WiFi 5 (802.11ac) and Bluetooth 5.3 BLE module (NXP 88W8997) 2x 100-pin 0.4mm pitch high-density UCM connectors Display 4-lane MIPI-DSI up to 1920 x 1080 @ 60Hz 4-lane LVDS up to 1366 […]

June 12, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

Tiny STM32MP135 system-on-module comes with up to 512MB RAM, 256MB NAND flash or 4GB eMMC flash

MYiR Technology’s MYC-YF13X is a system-on-module powered by the latest STMicro STM32MP135 cost-optimized Cortex-A7 microprocessor with 256MB or 512MB DDR3L, 256MB NAND Flash or 4GB eMMC flash, and 32Kbit EEPROM. The new MYC-YF13X has the same 39x37mm stamp-size form factor as the company’s earlier MYC-YA15XC-T CPU module based on the STM32MP15 Cortex-A7 processor, and a development board is also provided with LCD and camera interfaces, dual Gigabit Ethernet, RS485/RS232/CAN bus interfaces, and more. MYC-YF13X specifications: SoC – STMicro STM32MP135 (STM32MP135DAF7) single-core Cortex-A7 processor up to @ 1 GHz Two configurations for memory and storage 256MB DDR3L, 256MB NAND Flash, 32KB EEPROM or 512MB DDR3L, 4GB eMMC Flash, 32KB EEPROM 148-pin stamp hole expansion interface (1.0mm pitch) Display I/F – RGB Interface Camera – Parallel camera Audio – 4x I2S, 2x SAI Networking – 2x RGMII interface USB – 2x USB 2.0 Up to 8x UART Up to 5x I2C Up […]

June 11, 2023June 11, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Debian 12 “Bookworm” released with Linux 6.1

Debian 12 “Bookworm” operating system has been released with an update to Linux 6.1 LTS and a new non-free-firmware repository making it possible to separate non-free firmware from the other non-free packages. This follows the Debian 11 “Bullseye” release in August 2021, and the version of Debian will serve as the base for other Linux operating systems such as Ubuntu and derivates, Raspberry Pi OS, and so on. Debian 12 can be downloaded on a choice of desktop environments, namely Gnome 43, KDE Plasma 5.27, LXDE 11, LXQt 1.2.0, MATE 1.26, and Xfce 4.18. Bookworm includes a total of 64,419 packages many of which have been updated the to latest version. Nine architectures are supported by Debian 12 “Bookworm”: 32-bit PC (i386) and 64-bit PC (amd64) 64-bit ARM (arm64) ARM EABI (armel) ARMv7 (EABI hard-float ABI, armhf) little-endian MIPS (mipsel) 64-bit little-endian MIPS (mips64el) 64-bit little-endian PowerPC (ppc64el) IBM System […]

June 9, 2023July 28, 2023 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

A first look at i-Pi SMARC 1200 (Genio 1200) development kit

ADLINK Technology’s i-PI SMARC 1200 is an industrial prototyping kit for AI IoT and Robotics based on a SMARC 2.1 compliant LEC-MTK-I12000 system-on-module (SoM) powered by the MediaTek Genio 1200 (MT8395) octa-core Cortex-A78/A55 AIoT processor with a 4.8 TOPS AI processor. The company sent me a sample for evaluation and review, and in this first post, I’ll go through an unboxing and how to boot the system with the supported Yocto Linux or Ubuntu. i-Pi SMARC 1200 unboxing The i-Pi SMARC 1200 may be destined for industrial users, but it still comes with a neat retail package. The “i-Pi LEC-MTK-I1200-44-64G/EU” kit features a CPU module with 4GB LPDDR4 memory and 64GB UFS storage. The package includes the board itself preassembled in a desktop frame, a Quick Start Guide, a 19V/2.37A (45W) power adapter with an EU power cord, a micro USB to USB cable for debugging, and two bits for […]

June 9, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

Axiomtek AIE110-XNX is an affordable Edge AI Developer Kit based on NVIDIA Jetson Xavier NX

Axiomtek AIE110-XNX Edge AI developer kit provides up to 21 TOPS of accelerated AI computing performance thanks to an NVIDIA Jetson Xavier NX system-on-module with a 6-core NVIDIA Carmel ARM v8.2 64-bit CPU and a 384-core NVIDIA Volta GPU with 48 Tensor Cores. The new devkit serves as a relatively low-cost cost development kit with no minimum order, instead of getting full-feature embedded computers such as the company’s AIE900-XNX Edge AI system also based on the same Jetson Xavier NX module. Axiomtek AIE110-XNX specifications: NVIDIA Jetson Xavier NX system-on-module with CPU – 6-core NVIDIA Carmel Armv8.2 64-bit CPU with 6 MB L2 + 4 MB L3 cache GPU – 384-core NVIDIA Volta GPU with 48 Tensor Cores AI Accelerator – 2x NVDLA System Memory – 8GB 128-bit LPDDR4x onboard Storage – 16GB eMMC flash Storage – M.2 Key M 2280 with PCIe x4 NVMe SSD slot, microSD slot Video Output […]

June 7, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

reTerminal DM – A Raspberry Pi CM4-powered 10.1-inch HMI controller

reTerminal DM 10-inch Raspberry Pi CM4 HMI terminal

Seeed Studio’s reTerminal DM is an upgrade to the Raspberry Pi CM4-powered reTerminal with a larger 10.1-inch touchscreen display and a greater range of features and interfaces for various industrial applications. Described as a “Panel PC, HMI, PLC, IIoT Gateway all-in-one device”, the new reTerminal DM notably supports 12V-24V variable DC input and optionally PoE power input, its front panel is rated IP65 for protection against liquids and dust, a range of wired and wireless connectivity options are offered, and it also includes some serial and digital input and output interfaces. reTerminal DM specifications: SoM – Raspberry Pi Compute Module 4 with Broadcom BCM2711 quad-core Cortex-A72 processor @ 1.5 GHz, up to 8GB RAM, up to 32GB flash Storage – Optional M.2 NVMe SSD via M.2 2280 Key-M slot Display – 10.1-inch display with 1280 x 800 resolution, 10-point capacitive touchscreen 400-nit brightness, 170° H/V viewing angle Video Output – […]

June 6, 2023June 6, 2023 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

UP Squared i12 is a compact Alder Lake-P single board computer

AAEON’s UP Squared i12 is a single board computer with the same dimensions as the UP Squared (Apollo Lake) and UP Squared V2 (Elkhart Lake) boards, and mostly the same ports layout, but powered by a more powerful 12th generation Intel Alder Lake-P processor from a Celeron 7305E up to an Intel Core i7-1270PE. The board comes with up to 8 or 16GB LPDDR5 memory, SATA and NVMe storage support, triple 4K display support through HDMI, DisplayPort and USB-C interfaces, dual Gigabit Ethernet, a few USB boards, and some wafers and headers such as a Raspberry Pi-compatible GPIO header. UP Squared i12 specifications: 12th generation Alder Lake-P SoC: Intel Core i7-1270PE 12-core/16-thread processor @ 3.30GHz / 4.50GHz (Turbo) with 96EU Intel Xe graphics – PBP: 28W, up to 64W MTP Intel Core i5-1250PE 12-core/16-thread processor @ 3.20GHz / 4.40GHz (Turbo) with 80EU Intel Xe graphics – PBP: 28W, up to […]

June 3, 2023December 27, 2023 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

CrowVision review – An 11.6-inch 1366×768 touchscreen display that works with multiple SBCs

Raspberry Pi 4 CrowVision Touchscreen Display Tester

CrowVision is an 11.6-inch IPS capacitive touchscreen display with 1366×768 resolution that is designed to work not only with the Raspberry Pi but most single board computers with mounting holes within a 100 x 80 mm rectangle. Elecrow sent me a sample so I’ll try it out with a Raspberry Pi, a Windows 11 mini PC, and a Ubuntu 22.04 laptop to make sure it works well with those operating systems. CrowVision unboxing The packages include the display module itself, a 12V/2A power adapter, USB Type-C and micro USB cables, an HDMI to mini HDMI cable, a micro HDMI to mini HDMI cable, two “ribbons” for cable management, a screwdriver, an OSD control board with five keys, and a user manual. The display does not come with an enclosure, so it’s better suited for DIY projects where users design their own enclosure or mounting solution. The control board is based […]