Linux Category - Page 168 of 597 - CNX Software

September 23, 2021February 27, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

DIY Spotify Box features custom-designed Allwinner V3s SBC

The Spotify Box is a small DIY device based on an Allwinner V3s single-core Cortex-A7 camera SoC and a wooden enclosure designed to play Spotify songs, and not much else… The device serves as a bridge between the official Spotify app and your home audio system connected through the RCA jacks of the box. and allowing you to connect your smartphone to your audio setup and stream music throughout your house. Spotify Box specifications: SoC – Allwinner V3s single-core Cortex-A7 processor @ 1.2 GHz with on-chip 64MB DDR2 Storage – MicroSD card slot for OS Audio – 2x RCA jack for left and right audio Connectivity 10/100M Ethernet RJ45 port 2.4 GHz 802.11b/g/n WiFi 4 and Bluetooth 4.2 via RTL8723DS module Misc – Push button, RGB LED Power Supply – 5V via USB-C port Evan Hailey selected Allwinner V3s over other processors such as NXP i.MX233 or Microchip SAM9N because […]

September 22, 2021September 22, 2021 by Jean-Luc Aufranc (CNXSoft) - 16 Comments

PiKVM v3 Raspberry Pi HAT offers KVM over IP on the cheap (Crowdfunding)

Last December, we wrote about the inexpensive DIY Pi-KVM board to add KVM over IP to the Raspberry Pi board mentioning PiKVM v3 was in the works with extra features such as onboard ATX power control. It turns out PiKVM v3 HAT has been on Kickstarter for about a month and raised close to $600,000 US from over 2,500 backers with just about two days to go at the time of writing. PiKVM v3 hardware features and specifications: Video & audio capture port – 1x HDMI input up to 1080p50 MIPI CSI-2 interface to Pi to visualize HDMI input USB 1x USB-C console port 1x USB-C power input port USB-OTG pins USB-C OTG port doing the emulation of a USB keyboard, mouse, Virtual CD-ROM or USB Flash Drive, USB-Ethernet, USB-Serial port, etc… Console – RJ45 console port Debugging – UART access pins Expansion SPI and an extra GPIO for the […]

September 22, 2021September 22, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

UP Xtreme i11 Edge Compute Enabling Kit supports 5G, WiFi 6, Myriad X AI accelerator cards

UP! Bridge the Gap, a brand belonging to AAEON Technology, has started taking pre-orders for the UP Xtreme i11 Edge Compute Enabling Kit, a mini PC based on the UP Xtreme i11 Edge Tiger Lake SBC that was first introduced last year, and formally launched last month. The mini PC is offered with Celeron 6305E up to Intel Core i7-1185GRE processor, optional DDR4 and SSD, M.2 sockets for 5G, WiFi 6, or an AI accelerator card based on Movidius Myriad X VPU., serial ports, as well as a Phoenix terminal connector to access some of the GPIOs. UP Xtreme i11 Edge Compute Enabling Kit specifications: Tiger Lake “E”/”GRE” SoC (one or the other) Intel Core i7-1185G7GRE quad-core/8-thread processor @ up to 4.4 GHz with 96 EU Intel Iris Xe Graphics; up to 28W TDP (cTDP 15W) Intel Core i5-1145G7GRE quad-core/8-thread processor @ up to 4.1 GHz with 80 EU Intel […]

September 22, 2021September 22, 2021 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

$25 “Raspberry Pi 3 mini” board comes with a camera interface, USB & I/Os headers

TPCast-VR, aka “Raspberry Pi 3 mini”, is a compact board based on Broadcom BCM2837 quad-core Cortex-A53 processor, and that should come as part of Element14’s Raspberry Pi customization program, just like the custom Raspberry Pi 3 SBC with eMMC flash designed for laundry gateways that I noticed a few months ago. The board was initially integrated into the power box of the TPCAST Wireless Adaptor for HTC Vive and Oculus Rift virtual reality headsets, but eventually found its way into other applications notably FPV drones, and it’s now sold separately, as we’ll see further below. I found about the board via a tweet from Will Whang who purchased it for under $20 at the beginning of the year, and discovered the connection with the TPCast wireless adapter. TPCast-VR board specifications: SoC – Broadcom BCM2837 quad-core Cortex-A53 processor @ 1.2GHz with Videocore IV GPU System Memory – 1GB RAM Storage – […]

September 21, 2021September 24, 2021 by Sponsored Post - No Comments

SMARC Modules With NXP i.MX 8M Plus Processor (Sponsored)

Low-power flagship for artificial intelligence – congatec is expanding its SMARC platform with a new module with an NXP i.MX 8M Plus processor especially for embedded AI applications. Thanks to the extensive ecosystem with an application-ready 3.5-inch carrier board, Basler cameras, and AI software stack, fast proof of concept is possible. That hasn’t always been so easy. Previously, it was usually much more difficult to use the latest processor technology from the Arm environment as a finished system than to implement the x86 environment. This is because, as a result of the historically large range of individually tailored custom designs used in large quantities, the ecosystem of system platforms is not that extensive. However, with the modular approach based on the SMARC computer-on-modules specification, it is now also possible to obtain standard form factors from the x86 box PC range with ARM processors. For example, the embedded computing specialist congatec […]

September 20, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Customize GStreamer build with only the features needed for your application

Thanks to a partnership between Collabora and Huawei is now possible to build Gstreamer with just the features required for a specific application, reducing the binary size for space-constrained embedded systems. Gstreamer is a very popular open-source multimedia framework used in a wide variety of projects and products, and with an impressive number of features spread over 30 libraries and more than 1600 elements in 230 plugins. This is not a problem on desktop PC and most smartphones, but the size of the binary may be too large for some systems, and until recently it was no easy way to customize GStreamer build for a specific application. But Collabora changed the code to allow gst-build to generate a minimal GStreamer build. The company built upon a new feature from GStreamer 1.18, released in September 2020, that makes it possible to build all of GStreamer into a single shared library named […]

September 19, 2021April 5, 2022 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

TVMosaic CE (Community Edition) server released as open source by DVBLogic

TVMosaic (formerly DVBLink) TV/PVR-server application has been released as a cross-platform open-source software, following the closure of DVBLink business last year. It used to be a commercial solution with support for digital TV tuners, live TV watching, PVR functions, DLNA, and more, and there was also a PVR client for Kodi that was part of the list of support PVR clients like TvHeadEnd. DVBLogic did not release the full source code due to licensing requirements, and instead, released the code for TVMosaic Community Edition (CE) server on Gitlab under an MIT license. Some of the missing features include: The Licensing engine since the server is now open-source DLNA server TVAdvisor electronic program guide (EPG) DVBLogic TVButler USB tuner support except in Windows TVMosaic is a cross-platform solution and is supposed to work on Windows 7 or higher, Ubuntu 16.04 LTS 64-bit or higher, Debian 9.1 64-bit or higher, MacOS, 10.12 […]

September 17, 2021April 5, 2022 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

A first look at Microchip PolarFire SoC FPGA Icicle RISC-V development board

Formally launched on Crowd Supply a little over a year ago, Microchip PolarFire SoC FPGA Icicle (codenamed MPFS-ICICLE-KIT-ES) was one of the first Linux & FreeBSD capable RISC-V development boards. The system is equipped with PolarFire SoC FPGA comprised a RISC-V CPU subsystem with four 64-bit RISC-V (RV64GC) application cores, one 64-bit RISC-V real-time core (RV64IMAC), as well as FPGA fabric. Backers of the board have been able to play with it for several months ago, but Microchip is now sending the board to more people for evaluation/review, and I got one of my own to experiment with. That’s good to have a higher-end development board instead of the usual hobbyist-grade board. Today, I’ll just have a look at the kit content and main components on the board before playing with Linux and FPGA development tools in an upcoming or two posts. Microchip PolarFire SoC FPGA Icicle Unboxing The board […]