Hardware Category - Page 759 of 1132 - CNX Software

November 30, 2016November 30, 2016 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

NXP Modular IoT Gateway Supports Thread, Zigbee, NFC, Bluetooth and WiFi Connectivity

NXP has just announced a modular IoT gateway solution for large node networks (>= 250 nodes) based on Volansys i.MX6UL system-on-module, supporting wireless communications protocols such as Thread, ZigBee, NFC through add-on modules, on top of Wi-Fi and Bluetooth 4.1. NXP Modular IoT Gateway specifications: SoM – Volansys i.MX6UL 200-pin SO-DIMM module with: SoC – NXP i.MX 6UL ARM Cortex A7 processor @ 528 MHz System Memory – 256MB to 1GB DDR3L RAM Storage – 1GB to 4GB NAND flash, optional 4GB to 16GB eMMC flash, EEPROM for device info PMIC, Mbit Ethernet PHY Wireless Connectivity Expansion Modules: PN7120 explorer board for NFC Kinetis KW41 module for Thread support JN5169 module for Zigbee support 2x MikroBUS headers Baseboard connectors / features: Storage – 1x micro SD slot Connectivity – 1x 10/100M Ethernet port, Murata WiFi 802.11 b/g/n & Bluetooth 4.1 + EDR module with external antenna connector USB – 2x […]

November 30, 2016November 30, 2016 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

You Can Buy AirPods-like Wireless Bluetooth Stereo Earbuds for $16 and Up

Most Bluetooth headsets on the market actually come with some sort of wire or holding mechanism, which may not always be convenient, for example I can’t use mine comfortably while lying down on the bed. But that to electronics miniaturization, companies have recently started to offer truly wireless Bluetooth earbuds, including Apple’s yet-to-be available $159 Airpods. This morning I noticed two similar products in new arrivals list, first with $59.99 QCY Q29 mini Earburds on GeekBuying, and then even cheaper, but not quite as good looking (and likely not so good sounding), “FreeStereo Twins Wireless Bluetooth v4.1 In-Ear Headset w/ Mic” on DealExtreme going for just $22.25 including shipping. Let’s start with QCY Q29 earbuds specifications: Connectivity – Bluetooth 4.1 with HFP, HSP, A2DP, AVRC protocols support; up to 5-10 meter range Built-in Microphone Charging port – pogo on earbuds, micro USB to storage/charging box Battery – 45mAh for up […]

November 30, 2016November 30, 2016 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

$59 HiFive1 Arduino Compatible Board is Powered by Sifive Open Source RISC-V MCU (Crowdfunding)

Royalty-free RISC-V instruction sets has been getting in the news in the last few years with various MMU designs from companies or projects like lowRISC, PULPino, and SiFive, and recently there are been rumors that Samsung may use RISC-V in their future IoT SoCs. Many projects are still in progress, and while you can get involved in OnChip Open-V MCU crowdfunding campaign to their get the MCU or a development board, the cost for the MCU ($49) and development board ($99) is a little on the high side, and delivery is expected in 2018 for most rewards. SiFive appears to have a more interesting open source RISC-V solution with HiFive1 Arduino compatible board going for $59 and slated to ship between December 2016 and February 2017. HiFive1 development board specifications: MCU – SiFive Freedom E310 (FE310) 32-bit RV32IMAC processor @ up to 320+ MHz (1.61 DMIPS/MHz) Storage – 128 Mbit […]

November 29, 2016December 5, 2016 by Jean-Luc Aufranc (CNXSoft) - 17 Comments

LeMaker HiKey 96Boards Board Sells for $29.70 (Promo)

[Update: The promo is over back!] You’d think Cyber Monday should be over by now, but ITEAD Studio still has a clearance with real 70% discount, as 96Boards hardware compliant LeMaker Hikey board is now sold for just $29.70 instead of the usual $99 price. A quick reminder of the specifications: SoC – HiSilicon Kirin 620 octa core Cortex A53 processor @ 1.2 GHz with ARM Mali-450MP4 GPU System Memory – 2 GB LPDDR3 @ 800 MHz Storage – 8GB eMMC + micro SD slot Video Output / Display – HDMI up to 1080p, MIPI-DSI interface Connectivity – 802.11 a/b/g/n Wi-Fi, Bluetooth 4.1 LE (WL1835MOD module) USB – 2x USB 2.0 host ports, 1x micro USB OTG Camera – MIPI CSI interface Debugging – UART header), unpopulated 10-pin JTAG header (back) Expansion headers 40-pin LS (Low Speed) Expansion connector – UART, I2C, 12x GPIOs, SPI, PCM, PWM, SYS_DCIN, 1.8V, 5V, […]

November 29, 2016November 30, 2016 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Grid-EYE Breakout Board is a $49 Low Resolution Thermal Camera Module

Thermal cameras can be really expensive pieces of equipment, and even the cheap 60×60 thermal cameras available on Aliexpress costs a little over $200. However, PURE Engineering has made an breakout board with Panasonic Grid-EYE infrared 8×8 array sensor that allows you to experiment with the technology, or integrate into your own projects for just $49. Grid-EYE breakout board features: Panasonic Grid-EYE AMG8834 64 pixel infrared / thermal camera sensor with 60 degree viewing angle using MEMS thermopile technology Pinout compatible with Arduino Zero, ST-NUCLEO board, and other 3.3V boards with I2C, VDD, GND, INT, and AD pins PUREModules PCB edge connectors with UART, GPIO, to interface with the company’s IoT board Power Supply – On-board regulator handles 3 to 5V input The Panasonic sensor transfers thermal presence, direction, and temperature values over I2C. The company wrote a demo for the module with an Arduino sketech and a Processing sketch […]

November 29, 2016November 29, 2016 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Canon 4K600STZ 4K UHD Laser Projector Delivers up to 6,000 Lumens

At the beginning of the year, I wrote about Texas Instruments’ DLP technology for affordable 4K projectors, and the company’s DLP 0.67″ digital micromirror device (DMD) was expected to be found in 4K projector in the second half of 2016. So I went on Amazon, and I could find lots of “4K UHD projectors” with prices starting at $599, but if we look into details we may find some of those are “4K projector” with a 1280×800 resolution… And many of the ones selling in the $2,000+ range don’t list their native resolution with many able to handle 4K input, but actually projecting at 1920×1080 as can be seen in the table below. The most honest companies promote those models as “projectors with 4K Enhancement”, but if you want a true 4K projector, the cheapest option is probably Sony VPL-VW350ES that goes for close to $10,000 on Amazon. CNET has […]

November 29, 2016November 29, 2016 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Theobroma Announces Rockchip RK3368 and RK3399 Qseven System-on-Modules

Theobroma Systems, an embedded system company based in Austria, has designed several Allwinner systems-on-module compliant with μQseven & Qseven standards in the past. The company has now started to work with Rockchip and reached “an advanced design stage” for the development of μQseven and QSeven systems-on-module powered by RK3368 and RK3399 processors. RK3368-uQ7 module specifications: SoC – Rockchip RK3368 octa-Core ARM Cortex-A53 processor up to 1.2GHz with Imagination Technologies PowerVR G6110 GPU System Memory – up to 4GB DDR3-1600 SDRAM on-module (512MB, 1GB, 2GB (default) and 4GB configuration available) Storage – Up to 128GB eMMC flash on-module (8GB default), 16 Mbit to 128 Mbit SPI NOR flash on-module Video Capabilities – H.264 decoding up to 2160p30, H.265 decoding up to 2160p60, video encoding up to 1080p30 Connectivity – GbE PHY on-module CAN – On-module communication offload controller for CAN 230-pin MXM edge connector with: 10/100/1000 Mbps Ethernet USB – 1x […]

November 28, 2016November 28, 2016 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Getting Started with Pine64 PADI IoT Stamp – Part 2: Serial Console, GCC SDK, Flashing & Debugging Code

PADI IoT Stamp module powered by Realtek RTL8710AF ARM Cortex M3 WiFi SoC is a potential competitor to Espressif ESP8266 modules. Pine64, the manufacturer of the module, sent me their kit with a $2 IoT stamp, a breakout board, a USB to TTL debug board and a J-Link debug board. In the first part of the review I’ve shown the hardware and how to assemble PADI IoT stamp kit. In the second part I’m going to write a tutorial / getting start guide showing how to control the board with AT commands, build the firmware with GCC SDK, and finally demonstrate how to flash and debug the firmware with the J-Link debugger. The Quick Start Guide indicates you need to connect the USB to TTL debug board to UART2 instead of UART1 as I did on the very similar B&T RTL-00 RTL8710AF module, and set connection settings to 38400 8N1. […]