Hardware Category - Page 1171 of 1183 - CNX Software

October 6, 2011 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

AMD G-Series QSeven Module Conga-QAF by Congatec

Congatec announced the Conga-QAF, a Qseven module powered by AMD G-Series embedded processors. The module will come with either the AMD G-T40R single core or the AMD G-T40E dual core processor, with 2 GB DRAM by default (expandable to 4GB), numerous I/O interfaces and an optional on-board SSD with a capacity of up to 32 GB. If you are not familiar with the QSeven Form Factor and why it is used, please read the beginning of the blog post entitled “QSeven Form Factor Embedded Boards by Seco“. To summarize, this is a standard to allow developers to use modules (based on QSeven specs) to test their software on several processors by inserting those modules in a common main board. Here are the specification of the Conga-QAF Qseven module: CPU AMD G-T40E 1.0 GHz Dual Core (L1 cache 64KB, L2 cache 512kB x2, 6.4 W) AMD G-T40R 1.0 GHz Single Core […]

October 6, 2011October 6, 2011 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

60 USD Android Tablet: Aakash UbiSlate 7 Tablet

After much delay, the low cost tablet promised by the Indian government is finally released. The Aakash UbiSlate 7 is designed primarily for Indian students and will be sold to them at a discount. The tablet will be manufactured by Datawind in Hyderabad, India. The retail price will be 2,999 Rupees (~61 USD), but it will be sold to the government for 2250 Rupees (~46 USD) and will end up in the hands of students for a sponsored price of 1300 Rupees (~26 USD). Here are Aakash UbiSlate 7 Tablet Specifications: Processor: 366MHz Conexant Processor Memory: 256MB RAM Storage: 2GB Flash memory + 2GB Micro SD card (expandable to 32GB) OS: Android 2.2 with Getjar Marketplace (not the default Android Marketplace) Display: 7″ resistive touchscreen Network: Wifi only. Later models will be GPRS and SIM enabled. USB: 2 x ports Audio out: 3.5mm jack / Audio in: 3.5mm jack Battery: […]

September 28, 2011November 1, 2011 by Jean-Luc Aufranc (CNXSoft) - No Comments

CraneBoard: Low Cost Development Board based on TI AM3517

The CraneBoard is a low-cost, open-source hardware development platform based on the AM3517 Sitara ARM Cortex-A8 microprocessor. The CraneBoard was announced in December 2010, can be purchased for 199 USD and can be an alternative to the Beagleboard-xM. AM3517 is especially suited to industrial applications and would be a preferable platform if your project needs CAN or PoE support. The board has less RAM (256 MB vs. 512MB) and no camera port. Here are the features and specifications of the board (I highlighted the differences with Beagleboard-xM in green): AM3517 Sitara ARM Cortex-A8 – 600MHz Integrated 3D Graphics Accelerator RAM: 256 MB NAND Flash: 256MB Support for on-chip peripherals: 10/100 EMAC USB OTG utilizing on-processor PHY 3.3V I/O CAN Bus DDR2 Power over Ethernet and other power options including USB and DC MMC/SD Card Support Fully open-source four-layer PCB Fully Open Source Linux Board Support package (2.6.32) Based on existing […]

September 22, 2011September 22, 2011 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

99 USD OMAP3 Based Overo Computer On Module by Gumstix

Gumstix has manufactured its Overo COMS based on OMAP3503 and OMAP3530 since 2008. They have now announced a new low cost version named Overa Sand that sells for 115 USD per unit or less than 99 USD per unit for orders of 1,000 units or more. Overo Sand COM is Gumstix’s most basic computer-on-module with 256MB RAM and no on-board NAND. Here are the board specifications and features: Processor: Texas Instruments OMAP 3503 Applications Processor: – ARM Cortex-A8 CPU @ 600 Mhz Memory: 256MB RAM NO On-Board NAND Included Features: microSD card slot TPS65950 Power Management Expandability: via one 140-pin expansion board of Gumstix Overo series or custom, 140-pin expansion board via 27-pin camera board Connections: – (2) 70-pin connectors with 140 signals for: – I2C, PWM lines (6), A/D (6), 1-wire – UART, SPI, Extra MMC lines – Headset, Microphone – Backup battery – High Speed USB Host and […]

September 21, 2011September 21, 2011 by Jean-Luc Aufranc (CNXSoft) - No Comments

Archos G9 Android 3.2 Tablets Are Now Officially Available

Archos announced that Archos G9 Tablets are now available. There is of course a caveat to this… Only Archos 80 G9 Tablet can be purchased on Archos Store (limited availability) for 299.99 USD, all other models show the dreaded icon “Coming Soon”. However, all Archos G9 models can be pre-ordered on Amazon France but they are not yet available on Amazon US. The other disappointment is that the Turbo versions appear to have been clocked down to 1.2 Ghz, whereas they were previously announced at 1.5 Ghz. Having said that, if you click on “Product Information” on Archos website, it still says “ARM dual-core CORTEX A9 OMAP™ 4 up to 1.5 GHz”. There is also still a lot of confusion about the amount of RAM in the device 512 MB or 1 GB as this is not shown in the specifications. That’s quite a mess, it’s confusing and somewhat frustrating. […]

September 20, 2011September 20, 2011 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

First ARM-Based Arduino Board with Atmel SAM3U

Arduino announced Arduino Due board with a 32bit Cortex-M3 ARM processor on their blog before Maker Faire. The SAM3U processor from ATMEL runs at 96MHz with 256Kb of Flash, 50Kb of SRAM, 5 SPI buses, 2 I2C interfaces, 5 UARTS, 16 Analog Inputs at 12Bit resolution and more. Contrary to previous hardware release, they intend to open the process to the community early on and they plan to to be demo the board and give away some boards to a selected group of developers who will be invited to shape the platform while it’s been created. After Maker Faire, a small batch of Developer Edition boards on the Arduino store will be sold to members of the community who want to join the development effort. The final board will be released by the end of 2011. If you can’t wait there are some other Arduino-like projects with Cortex-M3 support based […]

September 14, 2011September 14, 2011 by Jean-Luc Aufranc (CNXSoft) - No Comments

Sony Announced the Android Walkman NW-Z1000

Sony Corp announced three new series of its Walkman portable music including the “NW-Z1000” series powered by Nvidia Tegra 2, equipped with an 4.3-inch TFT LCD panel and running Android 2.3 (gingerbread). NW-Z1000 user interface is slightly customized and its sound quality is improved thanks to a digital amplifier chip called “S-Master MX.” The changes made to the UI include shortcut icons for Sony’s music applications and video players at the bottom of the screen. The NW-Z1000 has wireless LAN capability, GPS and sensors such as acceleration sensor and is pre-installed with GMS (Google Mobile Service) which includes Google Maps, YouTube and Android Market. Here are the specifications of the NW-Z1000 series Walkmans: Android 2.3 with access to the Google market YouTube, Gmail, Google Maps and various Sony apps pre-installed (Sony Music Player, Photo Player, etc.) 4.3-inch LCD with 480×800 resolution NVIDIA Tegra 2 dual core mobile CPU (1GHz) 512MB main […]

September 14, 2011September 14, 2011 by Jean-Luc Aufranc (CNXSoft) - No Comments

Ziilabs Unveils Low Cost Jaguar3 Android Tablet Reference Designs

Earlier this May, Ziilabs announced the ZMS-20 dual core processors targeted at Android Honeycomb tablets. They have now unveil the 3rd generation of Android Tablet reference designs based on ZMS-20 and ZMS-40 called Jaguar3. Here’s an excerpt of the press release: ZiiLABS, a pioneering media processor and platforms company (a wholly-owned subsidiary of Creative Technology Ltd), today introduced its JAGUAR3, the most powerful 3rd Generation Android 3.2 tablet series. JAGUAR3 is a series of ultra-slim, ultra-lightweight and stylish 10.1” tablet reference designs targeted at the OEM markets. With over a decade of designing experience in portable mobile devices, Creative provided the ergonomic and sexy design of this series of JAGUAR3 tablets. ZMS-20 StemCell Processors JAGUAR3’s superior performance, low power consumption and rich feature set comes from the dual-core 1.5GHz ARM Cortex-A9 based ZMS-20 StemCell Processors. ZMS-20 has another 48 StemCell Processing cores within, which effectively make it into a 50-core processor. […]