Author: Jean-Luc Aufranc (CNXSoft)

Jean-Luc started CNX Software in 2010 as a part-time endeavor, before quitting his job as a software engineering manager, and starting to write daily news, and reviews full time later in 2011.
Posted on by Jean-Luc Aufranc (CNXSoft) - 36 Comments on Radxa X4 low-cost, credit card-sized Intel N100 SBC goes for $60 and up

Radxa X4 low-cost, credit card-sized Intel N100 SBC goes for $60 and up

Radxa X4 x86 Raspberry Pi 5 SBC

Radxa X4 is a credit card-sized Intel Processor N100 single board computer (SBC) that costs almost the same as a Raspberry Pi 5 with the 4GB RAM model going for about $60 and the 8GB RAM variant around $80. The x86 SBC offers many of the same features as the Raspberry Pi 5 including dual micro HDMI output, four USB 3.2/2.0 ports, Ethernet and WiFi networking, and the 40-pin GPIO header handled through a Raspberry Pi RP2040 microcontroller.  Networking is better with 2.5GbE and WiFi 6, M.2 SSD support is built-in and four to eight times faster compared to PCIe HAT for the Pi 5, and the USB 3.2 ports are capable of 10 Gbps speed. So let’s little not too like, and the main downside is the lack of MIPI CSI and DSI connectors for projects requiring those camera and display interfaces. Radxa X4 specifications: SoC – Intel Processor […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on How to easily enable MediaTek MT7922 Bluetooth on Ubuntu 24.04

How to easily enable MediaTek MT7922 Bluetooth on Ubuntu 24.04

MT7922 Bluetooth Ubuntu 24.04

MediaTek MT7922 WiFi 6 and Bluetooth 5.3 modules have recently been found in several mini PCs, but Bluetooth would not work in Linux due to a lack of drivers. In this post, we’ll show how to easily enable Bluetooth in MediaTek MT7922 modules when running Ubuntu 24.04. We previously noted that Ian Morrisson submitted a patch adding the IDs for the MT7922 module (Azurewave AW-XB591NF) used in recent GEEKOM mini PCs last March. In theory, you could have rebuilt the Linux kernel, but now that Linux 6.10 has been released, it’s much easier since Canonical has made the Linux 6.10 kernel available for Ubuntu, so we only need to install it and problem solved! Ubuntu 24.04 ships with Linux 6.8, we can see a Bluetooth opcode error in the kernel log.

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on $39 Acelink SM81 MediaTek Filogic 820 WiFi 6 system-on-module runs OpenWrt 23.05 or Debian 11

$39 Acelink SM81 MediaTek Filogic 820 WiFi 6 system-on-module runs OpenWrt 23.05 or Debian 11

ACELINK SM81 MediaTek Filogic 820 system-on-module

Acelink SM81 is a compact (50x36mm) system-on-module based on the MediaTek Filogic 820 (MT7981A/B) processor with WiFi 6 and Ethernet connectivity designed for IoT applications such as routers, access points, and gateways. The wireless module ships with up to 1GB DDR4 memory, a 2MB NOR flash for the bootloader, a 32GB eMMC flash for Linux or an optional NAND flash, and exposes various I/Os such as gigabit Ethernet, USB 3.0, PCIe 2.1, UART, and more through castellated holes. Acelink SM81 specifications: SoC (one or the other) MediaTek MT7981AA (Filogic 820) dual-core processor @ 1.3 GHz MediaTek MT7981BA (Filogic 820) dual-core processor @ 1.3 GHz without PCIe interface System Memory – 1GB DDR4 @ 2133 Mbps Storage 2MB NOR flash for bootloader 16GB or 32GB eMMC flash for main OS (OpenWrt) Footprint for NAND flash Wireless Radio Mode – 2.4GHz 2×2 + 5GHz 3×3  MIMO via MT7976CN RF IC Radio Frequency […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 8 Comments on MW-100-NAS Intel N100 motherboard features six SATA ports, two M.2 PCIe sockets, 2.5GbE and 10GbE interfaces

MW-100-NAS Intel N100 motherboard features six SATA ports, two M.2 PCIe sockets, 2.5GbE and 10GbE interfaces

MW-100-NAS motherboard

The MW-100-NAS mini-ITX motherboard is powered by an Intel Processor N100 Alder Lake-N CPU and seems especially suited for NAS (networked-attached storage) applications with six SATA connectors, two M.2 Key-M sockets for NVMe drivers, one 10GbE port, and two 2.5GbE RJ45 jacks. The motherboard supports up to 32GB DDR5 memory, features HDMI and DisplayPort video output ports, a COM port header, and plenty of external and internal USB interfaces. It takes power from a standard ATX connector. NW-N100-NAS motherboard specifications: SoC – Intel Processor N100 quad-core Alder Lake-N processor @ up to 3.4 GHz (Turbo) with 6MB cache, 24EU Intel HD graphics @ up to 750 MHz; TDP: 6W System Memory – Up to 32GB DDR5-4800 via SO-DIMM socket Storage 2x M.2 sockets for NVMe SSDs onboard 6x SATA connectors MicroSD card slot Video Output – 1x HDMI, 1x DisplayPort  Networking 2x 2.5GbE RJ45 ports via Intel i226-V controllers 1x […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 11 Comments on Panthor open-source driver achieves OpenGL ES 3.1 conformance with Arm Mali-G610 GPU (RK3588 SoC)

Panthor open-source driver achieves OpenGL ES 3.1 conformance with Arm Mali-G610 GPU (RK3588 SoC)

Panthor OpenGL ES 3.1 conformance Mali G610

Collabora has just announced that the Panthor open-source GPU kernel driver for third-generation Arm Valhall GPUs (Arm Mali-G310, Mali-G510, Mali-G610, and Mali-G710) has now achieved OpenGL ES 3.1 conformance with the Arm Mali-G610 GPU found in the Rockchip RK3588 SoC. Just a few days ago, Linux 6.10 was released with “support for Mali CSF-based GPUs found on recent Arm SoCs from Rockchip or Mediatek”, as expected from the earlier article entitled “Panthor open-source driver for Arm Mali-G310, Mali-G510, Mali-G610, and Mali-G710 GPUs to be part of Linux 6.10” published last March. But this did not say anything about the level of support for the Valhall GPU since it’s common for new hardware to be added with minimal support, and OpenGL ES 3.1 compliance means it’s ready for business… Collabora’s announcement explains this was tested on a Radxa Rock 5B single board computer: The conformance tests ran on a Rock5b board […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on StackyFi ESP32-S3 board features camera connector, 40-pin GPIO header for Raspberry Pi HAT (Crowdfunding)

StackyFi ESP32-S3 board features camera connector, 40-pin GPIO header for Raspberry Pi HAT (Crowdfunding)

StackyFi ESP32-S3 Raspberry Pi Zero board

SB Components’ StackyFi is an ESP32-S3 WiFi and Bluetooth IoT board with a 40-pin GPIO header compatible with most Raspberry Pi HAT expansion boards and a camera connector for image capture to a microSD card or machine learning applications. The Raspberry Pi Zero-sized board also comes with two USB Type-C ports, one “native” and the other for serial debugging, an IMU sensor, an RGB LED, and Boot and Reset buttons. The board can be powered through one of the USB-C ports or a LiPo battery. It partially builds upon the earlier StackPi board with a Raspberry Pi RP2040 microcontroller. StackyFi specifications: Wireless module – ESP32-S3-WROOM-1 MCU – ESP32-S3 dual-core Tensilica LX7 up to 240 MHz with 512KB SRAM Memory – TBD PSRAM Storage – TBD flash Wireless – WiFi 4 and Bluetooth LE 5 PCB antenna Storage – MicroSD card Camera I/F – FPC connector that works with OV2640 camera […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 6 Comments on Cervoz unveils tiny M.2 2230 2.5GbE PCIe expansion card

Cervoz unveils tiny M.2 2230 2.5GbE PCIe expansion card

Cervoz M.2 2230 2.5GbE PCIe expansion card

Cervoz MEC-LAN-2631i is a tiny, industrial-grade M.2 2230 (A+E key) PCIe Ethernet expansion card adding 2.5GbE networking to any system with a spare M.2 socket with a PCIe x1 interface. The card could be useful in case you want to add an extra 2.5GbE port, or for a system that lacks wired networking. It’s based on the Intel I226-IT 2.5Gbps Ethernet controller and can operate in the -40°C to 85°C temperature range as an industrial-grade module. Cervoz MEC-LAN-2631i specifications: Host interface – M.2 edge connector with PCIe 2.1 x1 up to 5.0/2.5GT/s Network – 10/100/1000/2500Mbps isolated interface based on an Intel I226-IT controller with an RJ45 port on a separate module Power Consumption – 350mA @ 3.3V Safety – Surge protection up to 2kV Dimensions – 30 x 22 mm; M.2 2230 (A+E key) form factor Temperature Range – Operating: -40°C to 85°C; storage: -40°C to 125°C Mounting – Cervoz’s […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on AAEON AQ7-ADN – A Qseven 2.1 system-on-module with Intel Alder Lake-N CPU, four PCIe Gen 3 x1 interfaces

AAEON AQ7-ADN – A Qseven 2.1 system-on-module with Intel Alder Lake-N CPU, four PCIe Gen 3 x1 interfaces

AAEON AQ7-ADN Alder Lake-N Qseven system-on-module

AAEON AQ7-ADN is a Qseven 2.1-compliant system-on-module based on Atom Processors x7425E, Intel Processor N, or Intel Core i3-N305 Alder Lake-N processor equipped with up to 8GB LPDDR5x and 64GB of eMMC flash storage. AAEON has already introduced Alder Lake-N COM Express and SMARC modules with the COM-ADNC6 and uCOM-ADN respectively, and the AQ7-ADN adds another system-on-module standard to its list of Alder Lake N-Series modules with a Qseven 2.1 SoM that offers four PCIe Gen x1 interfaces and a SATA storage interface. AAEON AQ7-ADN specifications: Alder Lake N-series SoC (one or the other) Intel Atom x7425E quad-core processor up to 3.4 GHz with 6MB cache, 24EU Intel UHD Graphics @ 1.00 GHz; TDP: 12W Intel Processor N50 dual-core processor up to 3.4 GHz with 6MB cache, 16EU Intel UHD Graphics @ 750 MHz; TDP: 6W Intel Processor N97 quad-core processor up to 3.6 GHz with 6MB cache, 24EU Intel […]

Exit mobile version
EmbeddedTS embedded systems design