FlexiPi is a bendable Raspberry Pi RP2040 board made of flexible PCB with the same layout as the original Raspberry Pi Pico, but featuring a USB-C port instead of a micro USB port on the official board.
This follows the Flexduino flex PCB clone of the Arduino UNO made by “EDISON SCIENCE CORNER”, but the smaller design of “TOP Gadgets” FlexiPi may make it potentially more useful since it could be inserted into tight or round enclosures.
FlexiPi specifications:
- MCU – Raspberry Pi RP2040 dual-core Cortex-M0+ microcontroller @ 48 MHz (overclockable to 133 MHz) with 264KB SRAM
- Storage – 2MB QSPI flash
- USB – 1x USB Type-C 1.1 port used for power and programming
- Expansion
- 2x 20-pin 2.54mm pitch header and castellated holes with 26 GPIOs, 3x 12-bit ADC up to 500 Kbps, 2x UART, 2x I2C, 2x SPI, 16x PWM, 2x programmable high-speed I/O
- 3.3V I/O voltage
- Sensor – 12-bit temperature sensor
- Debugging – 3-pin Arm Serial Wire Debug (SWD) port
- Misc
- BOOTSEL button
- WS2812 RGB LED
- RTC
- Power Supply – 5V via USB port or 1.8V to 5V DC via VSYS pin
- Dimensions – 51 x 21mm (thinner, bendable flexible PCB)
Apart from the USB-C port, RGB LED, and flexible PCB, the FlexiPi is the same as the Raspberry Pi Pico. That means it’s software-compatible and you can program it with the Raspberry Pi Pico C/C++ and MicroPython SDKs, Arduino, and any language supported by the Pico.
TOP Gadgets also provides three beginner’s guides for the board for C, MicroPython, and CircuitPyhon. Some of the photos imply those are printed out, but one of the rewards mentions eBooks, so you’d probably only get PDF files instead of physical books.
Making a low-volume flexible PCB comes at a cost, as the FlexiPi sells for five times more than the Raspberry Pi Pico, precisely $20 on Kickstarter. A bundle of 10 boards brings the price down to $18.50 per unit. Shipping is not included and adds an extra $15, so you’d need to pledge $35 to get the board delivered to your door by January 2025.
Jean-Luc started CNX Software in 2010 as a part-time endeavor, before quitting his job as a software engineering manager, and starting to write daily news, and reviews full time later in 2011.
Support CNX Software! Donate via cryptocurrencies, become a Patron on Patreon, or purchase goods on Amazon or Aliexpress
Would love to see the information in the article that Rust is a viable option for programming the Rp2040 and the newer RP2350 microcontrollers too
Can share more info if requested
Seriously why the hell run a campaign for the 2040 when it’s already been deprecated by a newer chip? The usual suspects (Adafruit, Sparkfun, etc) have all already released their upgraded 2350 boards and these guys are just now releasing a 2040 based project?
I have a sneaking suspicion this is just taking the open source PCB design of the Pico and dropping it on a flex PCB as a cash grab. I just can’t imagine why in the hell they wouldn’t just update the concept to use a non-outdated chip.
The uC isn’t “outdated”, It’s just of a lower/cheaper class than the pico2.
Arguably they would be better served by the new “hotness” but that doesn’t mean the Pico 1 doesn’t have it’s uses.
Not sure who would need it. If you have a bent/circular enclosure, you’ll probably already have a bendable board for it. SW use “normal” drvkits, and next step in the development phase design the board and enclosure..
I was wondering the same. Flex PCB costs more, is less reliable. And at the end of day I just don’t see too much use of that
This was suspended by Kickstarter a few days ago and there’s been no coverage or updates on sites like CNX.
Any idea why it was suspended?
They claim Kickstarter has not provided any reasons for the suspension.
That’s odd. Usually, it’s some kind of trademark reason (FlexiPi was used previously by some other products). Alternatively, it’s when it’s an obvious scam, but I did not see any red flags for this campaign.